Central tube fiber cable: find the bundle before the color
A central tube fiber cable carries all of its fibers in one buffer tube at the center of the cable, with the strength elements around that tube or in the jacket instead of a central strength member. Published sheets show it at low fiber counts and in drop cable, and some high-count ribbon cables use the same construction. For a splice tech, the practical difference is identification. With one tube, the tube color tells you nothing. Anything past 12 fibers has to be split into a bundle or a ribbon first, and only then does the fiber color mean anything.
What's actually inside the one tube
“Central tube” describes where the fibers sit, not how they're grouped. Three published designs show the range:
| Design | What the tube holds | How groups are told apart | Source |
|---|---|---|---|
| Low-count, up to 12 fibers | Loose fibers | No grouping needed: fiber color only | Prysmian Central Loose Tube 300 sheet |
| Bundled, past 12 fibers | Loose fibers in bundles of 12 | A binder around each bundle (LPI lists the colors) | LPI Central-Tube Unarmored catalog sheet; Prysmian Central Loose Tube 300 sheet |
| Ribbon | Stacked fiber ribbons | The ribbon's own marking, per the maker's sheet | CommScope OSP Fiber Cable Guide |
Prysmian's Central Loose Tube 300 sheet is a good example of the low-count end. It describes a single 3.0 mm central buffer tube, 1 to 12 or 24 fibers, gel or dry (24 fibers only in gel), and an 8.5 mm outside diameter. Its 24-fiber option is listed as two 12-fiber bundles in that one tube.
LPI's Central-Tube Unarmored cable runs from 2 to 48 fibers. Its catalog sheet says that past 12 fibers, the fibers are grouped in bundles of 12, each identified by a binder: blue, orange, green and brown.
At the other end, CommScope's outside plant cable guide says its drop cables are built with a central tube core design, and that its ribbon cables come in both stranded loose tube and central tube constructions. Its central tube ribbon families (D-CN-RB, D-CA-RB and the rollable D-CN-RR and D-CA-RR) run up to 864 fibers.
Strength members vary too, so don't assume them. LPI's sheet puts a steel rod in the outer sheath. Prysmian's says its flexible strength members bend in any direction. Read the cross-section on the sheet for the part number in hand before planning the entry.
The fundamentals: three checks, in order
Central tube cable gets treated as the easy cable because there's only one tube. That's backwards. With no tube colors to lean on, every bit of identification sits inside that one tube, and it all comes down to three checks.
1. Confirm the construction from the paperwork. Get the part number from the reel tag, sheath print, work order or as-builts, and find it on the maker's sheet. The sheet answers the questions that matter: is it loose fiber, bundles or ribbon, and how many fibers per group?
2. Identify the group before the fiber. On a bundled cable, the binder decides which dozen a fiber belongs to. If the binders run in the order LPI lists them (blue, orange, green, brown), an orange fiber can be fiber 2, 14, 26 or 38. The fiber color alone can't settle it. Anyone who has stopped over a loose orange fiber and suspected the count was right to stop, and that's why the binder comes before the color. On ribbon, identify the ribbon first, then read the fiber colors across it. Don't assume 12 per ribbon: CommScope's guide lists its 288- to 864-fiber flat ribbon central tube cables with 24 fibers per subunit.
3. Keep the group markers intact at entry. Cut a binder carelessly and the information it carried is gone. Loose fibers from two bundles look identical once they're mixed. Tag each group before any binder comes off.
Under TIA-598, the fiber colors themselves run blue, orange, green, brown, slate, white, red, black, yellow, violet, rose, aqua, the same sequence the 12 fiber color code page lays out in order.
Bundles inside one tube: where the counts go wrong
Twenty-four fibers in one tube can be marked more than one way, and the sheet doesn't always say which.
Prysmian's color code guide describes two schemes for a tube with more than 12 fibers. In one, a blue thread and an orange thread bind the fibers into two units: the blue unit holds fibers 1 to 12 and the orange unit holds 13 to 24, with no extra marking on the fibers. In the other, fibers 13 to 24 repeat the colors with black dashes, and fiber 20 is a natural fiber with a black dash. The guide names specific families for each scheme. Central Loose Tube 300 isn't one of the names, even though its own sheet lists the 24-fiber build as two 12-fiber bundles.
That gap is the honest limit here: not every central tube sheet spells out how the second dozen is marked. So look before counting. If there are binder threads, the threads are the identification. If there are no threads, check fiber 13 for a dash, ring or tracer. Prysmian Fiber Cable Colors walks through both schemes in more detail.
Entry: one tube means every fiber is exposed
On a stranded loose tube cable, a crew can open one buffer tube mid-span and leave the rest of the cable alone. CommScope's guide credits stranding with simplifying mid-span entries, and Loose Tube vs Ribbon Cable covers that trade from the splicing side.
Central tube doesn't offer that. Open the tube and every fiber in the cable is in front of you, including the ones that are only passing through. Prysmian works on the entry in other ways: its Central Loose Tube 300 sheet lists ezPrep armor for mid-entry, an optional ripcord, and notes that a single buffer tube means no empty filler tube to remove. The sheet still can't make the pass-through fibers less exposed. Treat a central tube entry as handling the whole cable, because it is.
The same build-first habit shows up across manufacturers. AFL Fiber Cable Configurations is a good example of one catalog with several ways to hold fibers, and the sheet for the exact part number settles each one.
Where Fiber Optic Color Code Lookup fits
Fiber Optic Color Code Lookup, the color code app from AllFiber, ships 199 cable configurations covering loose tube, ribbon, central tube and slotted core cable. They're a mix of manufacturer-specific layouts from 6 manufacturers and generic standards layouts, and Prysmian's Central Loose Tube 300 is one of the lines it carries. Pick the build that matches the cable, then use forward lookup (fiber number to color) or reverse lookup (the colors in front of you to the fiber number). The interactive cross-section diagram shows the layout.
Know what the app can't see. It can't read a reel tag, and it can't tell which binder a loose fiber came out of. Its Prysmian 24-fiber tube layouts show fibers 13 to 24 as the base colors with a black tracer, and fiber 20 as black with a white tracer. That gets the fiber order right, but on a binder-thread tube the fibers themselves carry no marks, so go by the binder. On ribbon builds, the same rule applies to markings: on AFL WTC and OFS AccuTube+ RR builds the app shows a color for each ribbon that the cable doesn't carry, so go by the ribbon number. If the build on screen doesn't match the maker's sheet, go by the sheet.
All 98,898 pre-computed lookups sit in a database bundled on the phone, so the app runs fully offline in a manhole or vault, without a signal. It carries 7 international color standards, switched in Settings. The full app is free for 24 hours with no account needed to start, then a single one-time $4.99 purchase, nothing recurring.
Frequently asked questions
What is a central tube fiber cable?
It's a cable that holds all of its fibers in a single buffer tube at the center, with strength elements around the tube or in the jacket rather than a central strength member. Fibers inside can be loose, grouped into bundles with colored binders, or stacked as ribbons. Published sheets show it at low fiber counts and in drop cable, and some ribbon cables use it at high counts.
How are fibers identified in a central tube cable with more than 12 fibers?
Identify the group first, then the fiber. On bundled designs, a colored binder marks each group of 12; LPI's catalog lists blue, orange, green and brown binders. On ribbon designs, the ribbon's marking comes first. Only then does the fiber color sequence apply. Keep binders intact at entry, because a loose fiber can't be traced back once they're cut.
Is central tube the same as loose tube?
Not quite. In both, fibers can sit loose inside a buffer tube, which is why Prysmian calls one of its designs Central Loose Tube 300. The difference is the number and placement of tubes. A stranded loose tube cable has several tubes wound around a central strength member, while a central tube cable has one tube in the middle holding everything.
Does Fiber Optic Color Code Lookup cover central tube cable?
Yes. Central tube is one of the cable types in its 199 cable configurations, which mix manufacturer-specific layouts from 6 manufacturers with generic standards layouts. All 98,898 lookups are bundled on the phone, so it works fully offline. The full app is free for 24 hours, then a one-time $4.99 purchase.